Item Tag: 1:64

1/64 Scale ’73 HONDA CIVIC CUSTOM Head Tail Light WaterSlide Decal for Custom Hot Wheels These waterslide decals work over any color! Inverted decals have white layer printed over inverted color layer, you install with printed white side touching car so that white layer become base layer. No need to clear coat before installing but you can but not recommended. Note: Car NOT included with orders. Only decals for sale. See digital preview. Be sure to check out my other decal sets available in my profile such as:-Universal Tire Letters-Universal Liveries-Universal Wraps-More Headlights and Taillights-More coming soon! 1/64 Scale Custom Wheels and Tires Sets also available on my shop! Any questions, feel free to ask! ——————————————————————————————————- HOW TO INSTALL: 1) Cut out around print as close as you can / feel comfortable doing. Use sharp scissors or blade2) Float on water for 15+ seconds3) Lightly wet area where decal will be placed so it can slide around easily4) Transfer decal from blue decal paper onto car with soft brush or finger5) Position as needed with brush, finger, or very gently with smooth toothpick 6) Absorb excess water with dry brush. Gently push out water from underneath decals.7) Optional but recommended: Clear coat entire car after adding decals for protection.—Once decals have been installed, wait at least 4 hours before adding Clear coat over entire car for protection.Avoid handling car or decals with oily fingers as they can cause weird results with clear coat! Pro tip: Use Micro Set and Micro Sol for better results…-apply some Micro Set liquid to area first, then transfer decal (try not to transfer too much water onto car)-Micro set is supposed to help decal stick to surfaces more easily (such as panel lines)-apply micro sol over decal to help it lay flat more easily (especially useful for complex surfaces or wrapping around edges)-be careful as micro sol will make decal more fragile, do not use too much, do not use if not needed-not needed for install but may help you ————————————————————————————————————————————————————————- SHIPPING INFO:All are flat rates, meaning it doesn’t matter how many items you buy, shipping price will be the same 🙂 For decals, axles, and/or spacers only!USA: $3.99 First Class Package with trackingInternational: $3.99 First Class Envelope without tracking For wheels, decals, axles, and/or spacers!USA: $4.99Canada: $9.99International: $12.99 If your total shipping cost is higher than above, click ‘Request Total’ in your cart so I can fix shipping cost.If not possible, no worries, I will refund any extra shipping costs paid for :)————————————————————————————————————————————————————————- Follow me on Social Media for updates on Restocks and New Releases!Any questions, feel free to ask 🙂

Easy to install wheels like Real Riders with rubber tires for Hot Wheels or any 1/64 Scale Cars..1 set is for 1 car.1 Wheel set includes 4 wheels, 4 tires, 2 fixed size axles which fit most cars but…I highly recommend you get Universal Axle Sets just in case axles aren’t the correct size..Size: 11.1 x 5.3mm.SMALL TE37s —–> https://www.ebay.com/itm/194883695182————————————————————————————————————————————————————————-HOW TO INSTALL: Drill method:1) Drill out base rivets with roughly a 9/64″ drill bit.2) Take car apart.3) Pry open / remove base tabs holding in original wheel axles.—for plastic bases, you can easily pry them open with small flathead screwdriver, or just snap them off with blade/wire cutters.—for metal bases, you may be able to snap them off with wire cutters (careful as this will send the tab flying across the room!) if you cannot remove the tab entirely, you will need to use dremel disc to grind off the rest of tab. —if you don’t care about the stock wheels/axles, you can also just bend them out to easily cut the axle with wire cutters4) Replace wheels/axles—if the custom wheels don’t fit because axle is too short/long, you will need to adjust custom axle sets, see below.5) Reassemble car.—If you didn’t overdrill, the base might just snap back together, otherwise you will need to lay car on it’s roof and add some super glue onto the posts where the rivets used to be, or use some epoxy putty.Optional: Lower car’s ride height by sanding down the interior that holds the axles.No Drill method:1) Cut stock axles with wire cutter.—you may need to bend the axles down to have room to cut them2) Use custom axles: —1. Bend axle pins about 10-15 Degrees with pliers—2. Insert bent pin into axle tube (if it won’t go in, you’ve bent it too much, unbend a bit and try again, if it slides out too easily, bend it more)—3. Insert 1 wheel into axle tube—4. Feed axle tube with wheel through car’s base—5. Insert another wheel into axle tube on the other side of car/axle—6. Insert bent axle pin into axle tube to lock in the wheels3) Adjust as needed.—if axle tube is too long: uninstall axle and trim with dremel disc and try again—if axle tube is too short (rare): pull out axle pins slightly—if there is play in the wheels, add spacers to fill in the gaps from wheel to base (you can make your own or use my 3D printed spacers for an easier time)Note: if you don’t use drill to open car, you can’t lower the car’s ride height.————————————————————————————————————————————————————————-Be sure to check out my other listings such as:-Real Riders 1/64 Scale Wheels and Tires-Headlight and Taillight Decals-Universal Liveries-Universal Wraps-Carbon Fiber Wrap-Side View Mirrors-Spacers Any questions, feel free to ask!————————————————————————————————————————————————————————-SHIPPING INFO: First Class Package with tracking Flat rate shipping: Doesn’t matter how many wheels/decals you buy!USA: $4.99 Canada: $9.99Worldwide: $12.99 If your total shipping cost is higher than above, click ‘Request Total’ in your cart so I can fix shipping cost. If not possible, no worries, i will refund any extra shipping costs paid for :)————————————————————————————————————————————————————————-Follow me on Social Media for updates on Restocks and New Releases!Any questions, feel free to ask 🙂